| Records |
| Author |
Trifonov, A.; Tong, C.-Y. E.; Blundell, R.; Ryabchun, S.; Gol'tsman, G. |
| Title |
Probing the stability of HEB mixers with microwave injection |
Type |
Journal Article |
| Year |
2015 |
Publication |
IEEE Trans. Appl. Supercond. |
Abbreviated Journal |
IEEE Trans. Appl. Supercond. |
| Volume |
25 |
Issue |
3 |
Pages |
2300404 (1 to 4) |
| Keywords |
NbN HEB mixer, stability, Allan-variance |
Abstract  |
Using a microwave probe as a tool, we have performed experiments aimed at understanding the origin of the output-power fluctuations in hot-electron-bolometer (HEB) mixers. We use a probe frequency of 1.5 GHz. The microwave probe picks up impedance changes of the HEB, which are examined upon demodulation of the reflected wave outside the cryostat. This study shows that the HEB mixer operates in two different regimes under a terahertz pump. At a low pumping level, strong pulse modulation is observed, as the device switches between the superconducting state and the normal state at a rate of a few megahertz. When pumped much harder, to approximate the low-noise mixer operating point, residual modulation can still be observed, showing that the HEB mixer is intrinsically unstable even in the resistive state. Based on these observations, we introduced a low-frequency termination to the HEB mixer. By terminating the device in a 50-Ω resistor in the megahertz frequency range, we have been able to improve the output-power Allan time of our HEB receiver by a factor of four to about 10 s for a detection bandwidth of 15 MHz, with a corresponding gain fluctuation of about 0.035%. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1051-8223 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1355 |
| Permanent link to this record |
| |
|
| |
| Author |
Kawamura, J.; Blundell, R.; Tong, C.-Y. E.; Golts'man, G.; Gershenzon, E.; Voronov B. |
| Title |
Superconductive NbN hot-electron bolometric mixer performance at 250 GHz |
Type |
Conference Article |
| Year |
1996 |
Publication |
Proc. 7th Int. Symp. Space Terahertz Technol. |
Abbreviated Journal |
Proc. 7th Int. Symp. Space Terahertz Technol. |
| Volume |
|
Issue |
|
Pages |
331-336 |
| Keywords |
NbN HEB mixers |
| Abstract |
Thin film NbN (<40 A) strips are used as waveguide mixer elements. The electron cooling mechanism for the geometry is the electron-phonon interaction. We report a receiver noise temperature of 750 K at 244 GHz, with / IF = 1.5 GHz, Af= 500 MHz, and Tphysical = 4 K. The instantaneous bandwidth for this mixer is 1.6 GHz. The local oscillator (LO) power is 0.5 1.tW with 3 dB-uncertainty. The mixer is linear to 1 dB up to an input power level 6 dB below the LO power. We report the first detection of a molecular line emission using this class of mixer, and that the receiver noise temperature determined from Y-factor measurements reflects the true heterodyne sensitivity. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
945 |
| Permanent link to this record |
| |
|
| |
| Author |
Trifonov, A.; Tong, C.-Y. E.; Lobanov, Y.; Kaurova, N.; Blundell, R.; Goltsman, G. |
| Title |
Photon absorption near the gap frequency in a hot electron bolometer |
Type |
Journal Article |
| Year |
2017 |
Publication |
IEEE Trans. Appl. Supercond. |
Abbreviated Journal |
IEEE Trans. Appl. Supercond. |
| Volume |
27 |
Issue |
4 |
Pages |
1-4 |
| Keywords |
NBN HEB mixer |
| Abstract |
The superconducting energy gap is a fundamental characteristic of a superconducting film, which, together with the applied pump power and the biasing setup, defines the instantaneous resistive state of the Hot Electron Bolometer (HEB) mixer at any given bias point on the I-V curve. In this paper we report on a series of experiments, in which we subjected the HEB to radiation over a wide frequency range along with parallel microwave injection. We have observed three distinct regimes of operation of the HEB, depending on whether the radiation is above the gap frequency, far below it or close to it. These regimes are driven by the different patterns of photon absorption. The experiments have allowed us to derive the approximate gap frequency of the device under test as about 585 GHz. Microwave injection was used to probe the HEB impedance. Spontaneous switching between the superconducting (low resistive) state and a quasi-normal (high resistive) state was observed. The switching pattern depends on the particular regime of HEB operation and can assume a random pattern at pump frequencies below the gap to a regular relaxation oscillation running at a few MHz when pumped above the gap. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
1558-2515 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1331 |
| Permanent link to this record |
| |
|
| |
| Author |
Trifonov, A.; Tong, C.-Y. E.; Lobanov, Y.; Kaurova, N.; Blundell, R.; Goltsman, G. |
| Title |
Gap frequency and photon absorption in a hot electron bolometer |
Type |
Conference Article |
| Year |
2016 |
Publication |
Proc. 27th Int. Symp. Space Terahertz Technol. |
Abbreviated Journal |
Proc. 27th Int. Symp. Space Terahertz Technol. |
| Volume |
|
Issue |
|
Pages |
121 |
| Keywords |
NbN HEB; Si membrane |
| Abstract |
The superconducting energy gap is a crucial parameter of a superconductor when used in mixing applications. In the case of the SIS mixer, the mixing process is efficient for frequencies below the energy gap, whereas, in the case of the HEB mixer, the mixing process is most efficient at frequencies above the gap, where photon absorption takes place more readily. We have investigated the photon absorption phenomenon around the gap frequency of HEB mixers based on NbN films deposited on silicon membranes. Apart from studying the pumped I-V curves of HEB devices, we have also probed them with microwave radiation, as previously described [1]. At frequencies far below the gap frequency, the pumped I-V curves show abrupt switching between the superconducting and resistive states. For the NbN HEB mixers we tested, which have critical temperatures of ~9 K, this is true for frequencies below about 400 GHz. As the pump frequency is increased beyond 400 GHz, the resistive state extends towards zero bias and at some point a small region of negative differential resistance appears close to zero bias. In this region, the microwave probe reveals that the device impedance is changing randomly with time. As the pump frequency is further increased, this random impedance change develops into relaxation oscillations, which can be observed by the demodulation of the reflected microwave probe. Initially, these oscillations take the form of several frequencies grouped together under an envelope. As we approach the gap frequency, the multiple frequency relaxation oscillations coalesce into a single frequency of a few MHz. The resultant square-wave nature of the oscillation is a clear indication that the device is in a bi-stable state, switching between the superconducting and normal state. Above the gap frequency, it is possible to obtain a pumped I-V curve with no negative differential resistance above a threshold pumping level. Below this pumping level, the device demonstrates bi-stability, and regular relaxation oscillation at a few MHz is observed as a function of pump power. The threshold pumping level is clearly related to the amount of power absorbed by the device and its phonon cooling. From the above experiment, we can derive the gap frequency of the NbN film, which is 585 GHz for our 6 μm thin silicon membrane-based device. We also confirm that the HEB mixer is not an efficient photon absorber for radiation below the gap frequency. 1. A. Trifonov et al., “Probing the stability of HEB mixers with microwave injection”, IEEE Trans. Appl. Supercond., vol. 25, no. 3, June 2015. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1204 |
| Permanent link to this record |
| |
|
| |
| Author |
Lobanov, Y.V.; Tong, C.-Y.E.; Hedden, A.S.; Blundell, R.; Voronov, B.M.; Gol'tsman, G.N. |
| Title |
Direct measurement of the gain and noise bandwidths of HEB mixers |
Type |
Journal Article |
| Year |
2011 |
Publication |
IEEE Trans. Appl. Supercond. |
Abbreviated Journal |
IEEE Trans. Appl. Supercond. |
| Volume |
21 |
Issue |
3 |
Pages |
645-648 |
| Keywords |
waveguide NbN HEB mixers |
| Abstract |
The intermediate frequency (IF) bandwidth of a hot electron bolometer (HEB) mixer is an important parameter of the mixer, in that it helps to determine its suitability for a given application. With the availability of wideband low noise amplifiers, it is simple to measure the performance of an HEB mixer over a wide range of IF at a fixed LO frequency using the standard Y-factor method. This in-situ method allows us to measure both the gain and noise bandwidths simultaneously. We have also measured mixer output impedance with a vector network analyser. Intrinsic time constant has been extracted from the impedance data and compared to the mixer's bandwidths determined from receiver Y-factor measurement. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
RPLAB @ gujma @ |
Serial |
720 |
| Permanent link to this record |
| |
|
| |
| Author |
Kawamura, J.; Blundell, R.; Tong, C.‐yu E.; Gol’tsman, G.; Gershenzon, E.; Voronov, B. |
| Title |
Performance of NbN lattice‐cooled hot‐electron bolometric mixers |
Type |
Journal Article |
| Year |
1996 |
Publication |
J. Appl. Phys. |
Abbreviated Journal |
J. Appl. Phys. |
| Volume |
80 |
Issue |
7 |
Pages |
4232-4234 |
| Keywords |
NbN HEB mixers |
| Abstract |
The heterodyne performance of lattice‐cooled hot‐electron bolometric mixers is measured at 200 GHz. Superconducting thin‐film niobium nitride strips with ∼5 nm thickness are used as waveguide mixer elements. A double‐sideband receiver noise temperature of 750 K at 244 GHz is measured at an intermediate frequency centered at 1.5 GHz with 500 MHz bandwidth and with 4.2 K device temperature. The instantaneous bandwidth for this mixer is 1.6 GHz. The local oscillator power required by the mixer is about 0.5 μW. The mixer is linear to within 1 dB up to an input power level 6 dB below the local oscillator power. A receiver incorporating a hot‐electron bolometric mixer was used to detect molecular line emission in a laboratory gascell. This experiment unambiguously confirms that the receiver noise temperature determined from Y‐factor measurements reflects the true heterodyne sensitivity. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0021-8979 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1607 |
| Permanent link to this record |
| |
|
| |
| Author |
Cao, Q.; Yoon, S. F.; Tong, C. Z.; Ngo, C. Y.; Liu, C. Y.; Wang, R.; Zhao, H. X. |
| Title |
Two-state competition in 1.3 μm multilayer InAs/InGaAs quantum dot lasers |
Type |
Journal Article |
| Year |
2009 |
Publication |
Applied Physics Letters |
Abbreviated Journal |
Appl. Phys. Lett. |
| Volume |
95 |
Issue |
19 |
Pages |
3 |
| Keywords |
2DEG |
| Abstract |
The competition of ground state (GS) and excited state (ES) is investigated from the as-grown and thermally annealed 1.3 μm ten-layer p-doped InAs/GaAs quantum dot (QD) lasers. The modal gain competition between GS and ES are measured and analyzed around the ES threshold characteristics. Our results show that two-state competition is more significant in devices with short cavity length operating at high temperature. By comparing the as-grown and annealed devices, we demonstrate enhanced GS and suppressed ES lasing from the QD laser annealed at 600 °C for 15 s. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
RPLAB @ gujma @ |
Serial |
673 |
| Permanent link to this record |
| |
|
| |
| Author |
Kawamura, Jonathan; Blundell, Raymond; Tong, C.-Y. Edward; Papa, D. Cosmo; Hunter, Todd R.; Gol'tsman, Gregory; Cherednichenko, Sergei; Voronov, Boris; Gershenzon, Eugene |
| Title |
First light with an 800 GHz phonon-cooled HEB mixer receiver |
Type |
Conference Article |
| Year |
1998 |
Publication |
Proc. 9th Int. Symp. Space Terahertz Technol. |
Abbreviated Journal |
Proc. 9th Int. Symp. Space Terahertz Technol. |
| Volume |
|
Issue |
|
Pages |
35-43 |
| Keywords |
HEB, mixer, LO power, local oscillator power, saturation effect, dynamic range |
| Abstract |
Phonon-cooled superconductive hot-electron bolometric (HEB) mixers are incorporated in a waveguide receiver designed to operate near 800 Gliz. The mixer elements are thin-film nio- bium nitride microbridges with dimensions of 4 nm thickness, 0.2 to 0.3 p.m in length and 2 jun in width. At 780 GHz the best receiver noise temperature is 840 K (DSB). The mixer IF bandwidth is 2.0 GHz, the absorbed LO power is —0.1 1.1W. A fixed-tuned version of the re- ceiver was installed at the Submillimeter Telescope Observatory on Mt. Graham, Arizona, to conduct astronomical observations. These observations represent the first time that a receiver incorporating any superconducting HEB mixer has been used to detect a spectral line of celes- tial origin. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
Pasadena, California, USA |
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
572 |
| Permanent link to this record |
| |
|
| |
| Author |
Edward Tong, C.-Y.; Loudkov, Denis N.; Paine, Scott N.; Marrone, Dan P.; Blundell, Raymond |
| Title |
Vector measurement of the beam pattern of a 1.5 THz superconducting HEB receiver |
Type |
Conference Article |
| Year |
2005 |
Publication |
Proc. 16th Int. Symp. Space Terahertz Technol. |
Abbreviated Journal |
Proc. 16th Int. Symp. Space Terahertz Technol. |
| Volume |
|
Issue |
|
Pages |
453-456 |
| Keywords |
NbTiN HEB mixers |
| Abstract |
Near-field vector beam pattern of the 1.5 THz superconducting Hot Electron Bolometer (HEB) receiver currently in operation in Northern Chile has been performed in our laboratory. Using an open waveguide probe, we have mapped both the amplitude and phase of the beam emerging from our 1.5 THz HEB receiver package, across a number of planes along the line of propagation of the radio-beam. With an integration time of about 100 ms per point, a signal-to-noise ratio of about 25 dB was achieved for a beam waist of 3.5 mm. These measurements have proved to be invaluable in achieving good alignment between the cryostat housing the HEB mixer and the remainder of the receiver and telescope optics. The accuracy of our beam measurement is estimated to be ±0.2 mm in position and ±5 arc minutes in angular displacement. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
|
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1474 |
| Permanent link to this record |
| |
|
| |
| Author |
Kawamura, J.; Blundell, R.; Tong, C.-yu E.; Gol’tsman, G.; Gershenzon, E.; Voronov, B.; Cherednichenko, S. |
| Title |
Low noise NbN lattice-cooled superconducting hot-electron bolometric mixers at submillimeter wavelengths |
Type |
Journal Article |
| Year |
1997 |
Publication |
Appl. Phys. Lett. |
Abbreviated Journal |
Appl. Phys. Lett. |
| Volume |
70 |
Issue |
12 |
Pages |
1619-1621 |
| Keywords |
NbN HEB mixers |
| Abstract |
Lattice-cooled superconducting hot-electron bolometric mixers are used in a submillimeter-wave waveguide heterodyne receiver. The mixer elements are niobium nitride film with 3.5 nm thickness and ∼10 μm2 area. The local oscillator power for optimal performance is estimated to be 0.5 μW, and the instantaneous bandwidth is 2.2 GHz. At an intermediate frequency centered at 1.4 GHz with 200 MHz bandwidth, the double sideband receiver noise temperature is 410 K at 430 GHz. The receiver has been used to detect molecular line emission in a laboratory gas cell. |
| Address |
|
| Corporate Author |
|
Thesis |
|
| Publisher |
|
Place of Publication |
|
Editor |
|
| Language |
|
Summary Language |
|
Original Title |
|
| Series Editor |
|
Series Title |
|
Abbreviated Series Title |
|
| Series Volume |
|
Series Issue |
|
Edition |
|
| ISSN |
0003-6951 |
ISBN |
|
Medium |
|
| Area |
|
Expedition |
|
Conference |
|
| Notes |
|
Approved |
no |
| Call Number |
|
Serial |
1599 |
| Permanent link to this record |
