|
|
Deang, J., Du, Q., & Gunzburger, M. D. (2002). Modeling and computation of random thermal fluctuations and material defects in the Ginzburg–Landau model for superconductivity. J. Comp. Phys., 181(1), 45–67.
Abstract: It is well known that thermal fluctuations and material impurities affect the motion of vortices in superconductors. These effects are modeled by variants of a time-dependent Ginzburg-Landau model containing either additive or multiplicative noise. Numerical computations are presented that illustrate the effects that noise has on the dynamics of vortex nucleation and vortex motion. For an additive noise model with relatively low variances, it is found that the vortices form a quasi-steady-state lattice in which the vortex core sizes remain roughly fixed but their positions vibrate. Two multiplicative noise models are considered. For one model having relatively long-range order, the sizes of the vortex cores vary in time and from one vortex to another. Finally, for the additive noise case, we show that as the variance of the noise tends to zero, solutions of the stochastic time-dependent Ginzburg-Landau equations converge to solutions of the corresponding equations with no noise.
|
|
|
|
Hoevers, H. F. C., Bento, A. C., Bruijn, M. P., Gottardi, L., Korevaar, M. A. N., Mels, W. A., et al. (2000). Thermal fluctuation noise in a voltage biased superconducting transition edge thermometer. Appl. Phys. Lett., 77(26), 4421–4424.
Abstract: The current noise at the output of a microcalorimeter with a voltage biased superconducting transition edge thermometer is studied in detail. In addition to the two well-known noise sources: thermal fluctuation noise from the heat link to the bath and Johnson noise from the resistive thermometer, a third noise source strongly correlated with the steepness of the thermometer is required to fit the measured noise spectra. Thermal fluctuation noise, originating in the thermometer itself, fully explains the additional noise. A simple model provides quantitative agreement between the observed and calculated noise spectra for all bias points in the superconducting transition.
|
|
|
|
Burke, P. J., Schoelkopf, R. J., Prober, D. E., Skalare, A., Karasik, B. S., Gaidis, M. C., et al. (1998). Spectrum of thermal fluctuation noise in diffusion and phonon cooled hot-electron mixers. Appl. Phys. Lett., 72(12), 1516–1518.
Abstract: A systematic study of the intermediate frequency noise bandwidth of Nb thin-film superconducting hot-electron bolometers is presented. We have measured the spectrum of the output noise as well as the conversion efficiency over a very broad intermediate frequency range (from 0.1 to 7.5 GHz) for devices varying in length from 0.08 μm to 3 μm. Local oscillator and rf signals from 8 to 40 GHz were used. For a device of a given length, the spectrum of the output noise and the conversion efficiency behave similarly for intermediate frequencies less than the gain bandwidth, in accordance with a simple thermal model for both the mixing and thermal fluctuation noise. For higher intermediate frequencies the conversion efficiency decreases; in contrast, the noise decreases but has a second contribution which dominates at higher frequency. The noise bandwidth is larger than the gain bandwidth, and the mixer noise is low, between 120 and 530 K (double side band).
|
|
|
|
Kawakami, A., Saito, S., & Hyodo, M. (2011). Fabrication of nano-antennas for superconducting Infrared detectors. IEEE Trans. Appl. Supercond., 21(3), 632–635.
Abstract: To improve the response performance of superconducting infrared detectors, we have developed a fabrication process for nano-antennas. A nano-antenna consists of a dipole antenna, and a superconducting thin film strip placed in the antenna's center. By measuring the transition temperature of the superconducting strips, we confirmed that their superconductivity maintained a good condition after the nano-antenna fabrication process. We also evaluated nano-antenna characteristics using Fourier transform infrared spectroscopy. The evaluated antenna length and width were respectively set at around 2400 nm and 400 nm, and the antennas were placed at intervals of several micrometers around the area of 1 mm2 . In an evaluation of spectral transmission characteristics, clear absorption caused by antenna effects was observed at around 1400 cm-1. High polarization dependencies were also observed.
|
|
|
|
Ikuta, R., Kusaka, Y., Kitano, suyoshi, Kato, H., Yamamoto, T., Koashi, M., et al. (2011). Wide-band quantum interface for visible-totelecommunication wavelength conversion. Nat. Comm., 2, 5.
Abstract: Although near-infrared photons in telecommunication bands are required for long-distance quantum communication, various quantum information tasks have been performed by using visible photons for the past two decades. Recently, such visible photons from diverse media including atomic quantum memories have also been studied. Optical frequency down-conversion from visible to telecommunication bands while keeping the quantum states is thus required for bridging such wavelength gaps. Here we report demonstration of a quantum interface of frequency down-conversion from visible to telecommunication bands by using a nonlinear crystal, which has a potential to work over wide bandwidths, leading to a high-speed interface of frequency conversion. We achieved the conversion of a picosecond visible photon at 780 nm to a 1,522-nm photon, and observed that the conversion process retained entanglement between the down-converted photon and another photon.
|
|
