| Home | << 1 2 >> |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Maslennikova, Anna; Tretyakov, Ivan; Ryabchun, Sergey; Finkel, Matvey; Kaurova, Natalia; Voronov, Boris; Gol’tsman, Gregory | ||||
| Title | Gain bandwidth and noise temperature of NbN HEB mixers with simultaneous phonon and diffusion cooling | Type | Abstract | ||
| Year | 2010 | Publication | Proc. 21th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 21th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 218-219 | ||
| Keywords | |||||
| Abstract | The space observatory Millimetron will be operating in the millimeter, sub-millimeter and infrared ranges using a 12-m cryogenic telescope in a single-dish mode, and as an interferometer with the space-earth and space-space baselines (the latter after the launch of the second identical space telescope). The observatory will allow performing astronomical observations with an unprecedented sensitivity (down to nJy level) in the single-dish mode, and observations with a high angular resolution in the interferometer mode. The total spectral range 20 μm – 2 cm is separated into 10 bands. HEB mixers with two cooling channels (diffusion and phonon) have been chosen to be the detectors of choice of the system covering the range from 1 THz to 6 THz as the best detectors in terahertz receivers. This type of HEB has already shown good work in the terahertz range. A gain bandwidth of 6 GHz at an LO frequency of 300 GHz and a noise temperature of 750 K at an LO frequency of 2.5 THz are the best values for HEB mixers with two cooling channels [1]. Theoretical estimations predict a bandwidth up to 12 GHz. Reaching such good result demands more systematic and thorough research. We present the results of the gain bandwidth and noise temperature measurements for superconducting hot- electron bolometer mixers with two cooling channels. These characteristics of the devices of lengths varying from 50 to 200 nm were measured for the purposes of Millimetron at frequencies of 600 GHz, 2.5 THz, and 3.8 THz. For gain bandwidth measurements we use two BWO’s operating at 600 GHz: one as the signal and the second as the LO. The noise temperature measurements were performed using a gas discharge laser as the LO and blackbodies at 77 K and 295 K as input signals. The devices studied consist of 3.5-nm-thick NbN bridges connected to thick (10 nm) high conductivity Au leads fabricated in situ. This method of fabricating devices has already proved promising by opening the diffusion cooling channel. [2] Fig. 1 shows a SEM photograph of a log-spiral antenna with an HEB at its apex. Fig. 1. Left: a SEM photograph of a log-spiral antenna with an HEB at its apex; right: a close-up of the HEB at the antenna apex. [1] S. A. Ryabchun, I. V. Tretyakov, M. I. Finkel, S. N. Maslennikov, N. S. Kaurova, V. A. Seleznev, B. M. Voronov, and G. N. Gol’tsman, NbN phonon-cooled hot-electron bolometer mixer with additional diffusion cooling, Proc. of the 20 th Int. Symp. Space. Technol., Charlottesville, Virginia, USA, April 20 – 22, 2009. 218[2] S. A. Ryabchun * , I. V. Tretyakov, M. I. Finkel, S. N. Maslennikov, N. S. Kaurova, V. A. Seleznev, B. M. Voronov and G. N. Goltsman, Fabrication and characterisation of NbN HEB mixers with in situ gold contacts, Proc. of the 19 th Int. Symp. Space. Technol., Groningen, The Netherlands, April 28-30, 2008 | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication  |
Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1393 | |||
| Permanent link to this record | |||||
| Author | Shurakov, Alexander; Maslennikov, Sergey; Tong, Cheuk-yu E.; Gol’tsman, Gregory | ||||
| Title | Performance of an HEB direct detector utilizing a microwave reflection readout scheme | Type | Conference Article | ||
| Year | 2015 | Publication | Proc. 26th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 26th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 36 | ||
| Keywords | HEB detector | ||||
| Abstract | We report the results of our study on the performance of a hot electron bolometric (HEB) direct detector, operated by a microwave pump. The HEB devices used in this work were made from NbN thin film deposited on high resistivity silicon with an in-situ fabrication process. The experimental setup employed is similar to the one described in [1]. The detector chips were glued to a silicon lens clamped to a copper holder mounted on the cold plate of a liquid helium cryostat. Thermal link between the lens and the holder was maintained by a thin indium shim. The HEBs were operated at a bath temperature of about 4.4 K. Conventional phonon pump, commonly realized by raising the bath temperature of the detector, was substituted by a microwave one. In this case, a CW microwave signal is injected to the device through a directional coupler connected directly to the detector holder. The power incident on the HEB device was typically 1-2 μW, and the pump frequency was in the range of 0.5-1.5 GHz. The signal sources were 2 black bodies held at temperatures of 295 K and 77 K. A chopper wheel placed in front of the cryostat window switched the input to the detector between the 2 sources. A modulation frequency of several kilohertz was chosen in order to reduce the effects of the HEB’s flicker noise. A cold mesh filter was used to define the input bandwidth of the detector. The reflected microwave signal from the HEB device was fed into a low noise amplifier, the output of which is connected to a room temperature Schottky microwave power detector. This Schottky detector, in conjunction with a lock-in amplifier, demodulated the input signal modulation from the copper wheel. As the input load was switched, the impedance of the HEB device at the microwave pump frequency also changed in response to the incident signal power variation. Therefore the reflected microwave power follows the incident signal modulation. The derived responsivity from this detection system nicely correlates with the HEB impedance. In order to provide a quantitative description of the impedance variation of the HEB device and the impact of a microwave pump, we have numerically solved the heat balance equations written for the NbN bridge and its surrounding thermal heat sink [2]. Our model also accounts for the impact of the operating frequency of the detector because of non-uniform absorption of low-frequency photons across the NbN bridge [3]. In our measurements we varied the signal source wavelength from 2 mm down to near infrared range, and hence we indirectly performed the impedance measurements at frequencies below, around and far beyond the superconducting gap. Preliminary results show good agreement between the experiment and theoretical prediction. Further measurements are still in progress. [1] A. Shurakov et al., “A Microwave Reflection Readout Scheme for Hot Electron Bolometric Direct Detector”, to appear in IEEE Trans. THz Sci. Tech., 2015. [2] S. Maslennikov, “RF heating efficiency of the terahertz superconducting hot-electron bolometer”, http://arxiv.org/pdf/1404.5276v5.pdf, 2014. [3] W. Miao et al., “Non-uniform absorption of terahertz radiation on superconducting hot electron bolometer microbridges”, Appl. Phys. Let., 104, 052605, 2014. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1158 | |||
| Permanent link to this record | |||||
| Author | Trifonov, Andrey; Tong, C. Edward; Lobanov, Yury; Kaurova, Natalia; Blundell, Raymond; Gol’tsman, Gregory | ||||
| Title | An investigation of the DC and IF performance of silicon-membrane HEB mixer elements | Type | Conference Article | ||
| Year | 2015 | Publication | Proc. 26th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 26th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 40 | ||
| Keywords | silicon-membrane HEB waveguide mixer | ||||
| Abstract | We report on our initial development towards a 2x2 multi-pixel HEB waveguide mixer for operation at 1.4 THz. We have successfully fabricated devices comprising an NbN bridge integrated with antenna test structure using a silicon membrane as the supporting substrate. DC measurements of the test chips demonstrate critical current from 0.1 – 1mA depending on the size of device, with T c of around 10 K and ΔTc ~ 0.8 K. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1160 | |||
| Permanent link to this record | |||||
| Author | Pyatkov, Felix; Khasminskaya, Svetlana; Fütterling, Valentin; Fechner, Randy; Słowik, Karolina; Ferrari, Simone; Kahl1, Oliver; Kovalyuk, Vadim; Rath, Patrik; Vetter, Andreas; Flavel, Benjamin S.; Hennrich, Frank; Kappes, Manfred M.; Gol’tsman, Gregory N.; Korneev, Alexander; Rockstuhl, Carsten; Krupke, Ralph; Pernice, Wolfram H. P. | ||||
| Title | Carbon nanotubes as exceptional electrically driven on-chip light sources | Type | Miscellaneous | ||
| Year | 2016 | Publication | 2Physics | Abbreviated Journal | 2Physics |
| Volume | Issue | Pages | |||
| Keywords | carbon nanotubes, CNT | ||||
| Abstract | Carbon nanotubes (CNTs) belong to the most exciting objects of the nanoworld. Typically, around 1 nm in diameter and several microns long, these cylindrically shaped carbon-based structures exhibit a number of exceptional mechanical, electrical and optical characteristics [1]. In particular, they are promising ultra-small light sources for the next generation of optoelectronic devices, where electrical components are interconnected with photonic circuits. Few years ago, we demonstrated that electically driven CNTs can serve as waveguide-integrated light sources [2]. Progress in the field of nanotube sorting, dielectrophoretical site-selective deposition and efficient light coupling into underlying substrate has made CNTs suitable for wafer-scale fabrication of active hybrid nanophotonic devices [2,3]. Recently we presented a nanotube-based waveguide integrated light emitters with tailored, exceptionally narrow emission-linewidths and short response times [4]. This allows conversion of electrical signals into well-defined optical signals directly within an optical waveguide, as required for future on-chip optical communication. Schematics and realization of this device is shown in Figure 1. The devices were manufactured by etching a photonic crystal waveguide into a dielectric layer following electron beam lithography. Photonic crystals are nanostructures that are also used by butterflies to give the impression of color on their wings. The same principle has been used in this study to select the color of light emitted by the CNT. The precise dimensions of the structure were numerically simulated to tailor the properties of the final device. Metallic contacts in the vicinity to the waveguide were fabricated to provide electrical access to CNT emitters. Finally, CNTs, sorted by structural and electronic properties, were deposited from a solution across the waveguide using dielectrophoresis, which is an electric-field-assisted deposition technique. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2372-1782 | ISBN | Medium | ||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1219 | |||
| Permanent link to this record | |||||
| Author | Shcherbatenko, Michael; Lobanov, Yury; Finkel, Matvey; Maslennikov, Sergey; Pentin, Ivan; Semenov, Alexander; Titova, Nadezhda; Kaurova, Natalya; Voronov, Boris M.; Rodin, Alexander; Klapwijk, Teunis M.; Gol’tsman, Gregory N. | ||||
| Title | Development of a 30 THz heterodyne receiver based on a hot-electron-bolometer mixer | Type | Abstract | ||
| Year | 2014 | Publication | Proc. 25th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 25th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 122 | ||
| Keywords | mid-IR NbN HEB mixers, GaAs substrates | ||||
| Abstract | We present new Hot-Electron-Bolometer (HEB) mixers designed for mid-IR spectroscopy targeting astrophysical and geophysical observations where high sensitivity and spectral resolution are required. The mixers are made of an ultrathin NbN film deposited on GaAs substrates. Two entirely different types of the devices have been fabricated. The first type is based on a direct radiation coupling concept and the mixing devices are shaped as squares of 5×5 μm 2 (which corresponds to the diffraction limit at the chosen wavelength) and 10×10 μm 2 (which was used to establish a possible influence of the contact pads on the radiation absorption). The second type utilizes a spiral antenna designed with HFSS. The fabrication and layout of the devices as well as the performance comparison will be presented. During the experiments, the HEB mixer was installed on the cold plate of a LHe cryostat. A germanium window and an extended semi-spherical germanium lens are used to couple the radiation. The cryostat is equipped with a germanium optical filter of thickness 0.5 mm and with a center wavelength of 10.6 mμ. The incident power absorption is measured by using the isothermal method. As a Local Oscillator, a 10.6 micrometers line of a CO2 gas laser is used. We further characterize the frequency response of the spiral antenna with a FIR-spectrometer. The noise characteristics of the mixers are determined from a room temperature cold load and a heated black body at ~600 K as a hot load. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication |
Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1364 | |||
| Permanent link to this record | |||||