| Home | << 1 2 >> |
|
| Records | |||||
|---|---|---|---|---|---|
| Author | Shurakov, Alexander; Maslennikov, Sergey; Tong, Cheuk-yu E.; Gol’tsman, Gregory | ||||
| Title | Performance of an HEB direct detector utilizing a microwave reflection readout scheme | Type  |
Conference Article | ||
| Year | 2015 | Publication | Proc. 26th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 26th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 36 | ||
| Keywords | HEB detector | ||||
| Abstract | We report the results of our study on the performance of a hot electron bolometric (HEB) direct detector, operated by a microwave pump. The HEB devices used in this work were made from NbN thin film deposited on high resistivity silicon with an in-situ fabrication process. The experimental setup employed is similar to the one described in [1]. The detector chips were glued to a silicon lens clamped to a copper holder mounted on the cold plate of a liquid helium cryostat. Thermal link between the lens and the holder was maintained by a thin indium shim. The HEBs were operated at a bath temperature of about 4.4 K. Conventional phonon pump, commonly realized by raising the bath temperature of the detector, was substituted by a microwave one. In this case, a CW microwave signal is injected to the device through a directional coupler connected directly to the detector holder. The power incident on the HEB device was typically 1-2 μW, and the pump frequency was in the range of 0.5-1.5 GHz. The signal sources were 2 black bodies held at temperatures of 295 K and 77 K. A chopper wheel placed in front of the cryostat window switched the input to the detector between the 2 sources. A modulation frequency of several kilohertz was chosen in order to reduce the effects of the HEB’s flicker noise. A cold mesh filter was used to define the input bandwidth of the detector. The reflected microwave signal from the HEB device was fed into a low noise amplifier, the output of which is connected to a room temperature Schottky microwave power detector. This Schottky detector, in conjunction with a lock-in amplifier, demodulated the input signal modulation from the copper wheel. As the input load was switched, the impedance of the HEB device at the microwave pump frequency also changed in response to the incident signal power variation. Therefore the reflected microwave power follows the incident signal modulation. The derived responsivity from this detection system nicely correlates with the HEB impedance. In order to provide a quantitative description of the impedance variation of the HEB device and the impact of a microwave pump, we have numerically solved the heat balance equations written for the NbN bridge and its surrounding thermal heat sink [2]. Our model also accounts for the impact of the operating frequency of the detector because of non-uniform absorption of low-frequency photons across the NbN bridge [3]. In our measurements we varied the signal source wavelength from 2 mm down to near infrared range, and hence we indirectly performed the impedance measurements at frequencies below, around and far beyond the superconducting gap. Preliminary results show good agreement between the experiment and theoretical prediction. Further measurements are still in progress. [1] A. Shurakov et al., “A Microwave Reflection Readout Scheme for Hot Electron Bolometric Direct Detector”, to appear in IEEE Trans. THz Sci. Tech., 2015. [2] S. Maslennikov, “RF heating efficiency of the terahertz superconducting hot-electron bolometer”, http://arxiv.org/pdf/1404.5276v5.pdf, 2014. [3] W. Miao et al., “Non-uniform absorption of terahertz radiation on superconducting hot electron bolometer microbridges”, Appl. Phys. Let., 104, 052605, 2014. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1158 | |||
| Permanent link to this record | |||||
| Author | Trifonov, Andrey; Tong, C. Edward; Lobanov, Yury; Kaurova, Natalia; Blundell, Raymond; Gol’tsman, Gregory | ||||
| Title | An investigation of the DC and IF performance of silicon-membrane HEB mixer elements | Type |
Conference Article | ||
| Year | 2015 | Publication | Proc. 26th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 26th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 40 | ||
| Keywords | silicon-membrane HEB waveguide mixer | ||||
| Abstract | We report on our initial development towards a 2x2 multi-pixel HEB waveguide mixer for operation at 1.4 THz. We have successfully fabricated devices comprising an NbN bridge integrated with antenna test structure using a silicon membrane as the supporting substrate. DC measurements of the test chips demonstrate critical current from 0.1 – 1mA depending on the size of device, with T c of around 10 K and ΔTc ~ 0.8 K. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1160 | |||
| Permanent link to this record | |||||
| Author | Lobanov, Yury V.; Tong, Cheuk-yu E.; Hedden, Abigail S.; Blundell, Raymond; Gol’tsman, Gregory N. | ||||
| Title | Microwave-assisted measurement of the frequency response of terahertz HEB mixers with a Fourier transform spectrometer | Type |
Conference Article | ||
| Year | 2010 | Publication | Proc. 21th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 21th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 420-423 | ||
| Keywords | |||||
| Abstract | We describe a novel method of operation of the HEB direct detector for use with a Fourier Transform Spectrometer. Instead of elevating the bath temperature, we have measured the RF response of waveguide HEB mixers by applying microwave radiation to select appropriate bias conditions. In our experiment, a microwave signal is injected into the HEB mixer via its IF port. By choosing an appropriate injection level, the device can be operated close to the desired operating point. Furthermore, we have shown that both thermal biasing and microwave injection can reproduce the same spectral response of the HEB mixer. However, with the use of microwave injection, there is no need to wait for the mixer to reach thermal equilibrium, so characterisation can be done in less time. Also, the liquid helium consumption for our wet cryostat is also reduced. We have demonstrated that the signal- to-noise ratio of the FTS measurements can be improved with microwave injection. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1394 | |||
| Permanent link to this record | |||||
| Author | Ryabchun, Sergey; Tong, Cheuk-yu Edward; Blundell, Raymond; Kimberk, Robert; Gol’tsman, Gregory | ||||
| Title | Stabilisation of a terahertz hot-electron bolometer mixer with microwave feedback control | Type |
Conference Article | ||
| Year | 2007 | Publication | Proc. 18th Int. Symp. Space Terahertz Technol. | Abbreviated Journal | Proc. 18th Int. Symp. Space Terahertz Technol. |
| Volume | Issue | Pages | 193-198 | ||
| Keywords | waveguide NbN HEB mixers, Allan variance, stability | ||||
| Abstract | We report on implementation of microwave feedback control loop to stabilise the performance of an HEB mixer receiver. It is shown that the receiver sensitivity increases by a factor of 4 over a 16-minute scan, and the corresponding Allan time increases up to 10 seconds, as opposed to an open loop value of 1 second. Our experiments also demonstrate that the receiver sensitivity is limited by the intermediate frequency chain. | ||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | ISBN | Medium | |||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1421 | |||
| Permanent link to this record | |||||
| Author | Pyatkov, Felix; Khasminskaya, Svetlana; Fütterling, Valentin; Fechner, Randy; Słowik, Karolina; Ferrari, Simone; Kahl1, Oliver; Kovalyuk, Vadim; Rath, Patrik; Vetter, Andreas; Flavel, Benjamin S.; Hennrich, Frank; Kappes, Manfred M.; Gol’tsman, Gregory N.; Korneev, Alexander; Rockstuhl, Carsten; Krupke, Ralph; Pernice, Wolfram H. P. | ||||
| Title | Carbon nanotubes as exceptional electrically driven on-chip light sources | Type |
Miscellaneous | ||
| Year | 2016 | Publication | 2Physics | Abbreviated Journal | 2Physics |
| Volume | Issue | Pages | |||
| Keywords | carbon nanotubes, CNT | ||||
| Abstract | Carbon nanotubes (CNTs) belong to the most exciting objects of the nanoworld. Typically, around 1 nm in diameter and several microns long, these cylindrically shaped carbon-based structures exhibit a number of exceptional mechanical, electrical and optical characteristics [1]. In particular, they are promising ultra-small light sources for the next generation of optoelectronic devices, where electrical components are interconnected with photonic circuits. Few years ago, we demonstrated that electically driven CNTs can serve as waveguide-integrated light sources [2]. Progress in the field of nanotube sorting, dielectrophoretical site-selective deposition and efficient light coupling into underlying substrate has made CNTs suitable for wafer-scale fabrication of active hybrid nanophotonic devices [2,3]. Recently we presented a nanotube-based waveguide integrated light emitters with tailored, exceptionally narrow emission-linewidths and short response times [4]. This allows conversion of electrical signals into well-defined optical signals directly within an optical waveguide, as required for future on-chip optical communication. Schematics and realization of this device is shown in Figure 1. The devices were manufactured by etching a photonic crystal waveguide into a dielectric layer following electron beam lithography. Photonic crystals are nanostructures that are also used by butterflies to give the impression of color on their wings. The same principle has been used in this study to select the color of light emitted by the CNT. The precise dimensions of the structure were numerically simulated to tailor the properties of the final device. Metallic contacts in the vicinity to the waveguide were fabricated to provide electrical access to CNT emitters. Finally, CNTs, sorted by structural and electronic properties, were deposited from a solution across the waveguide using dielectrophoresis, which is an electric-field-assisted deposition technique. |
||||
| Address | |||||
| Corporate Author | Thesis | ||||
| Publisher | Place of Publication | Editor | |||
| Language | Summary Language | Original Title | |||
| Series Editor | Series Title | Abbreviated Series Title | |||
| Series Volume | Series Issue | Edition | |||
| ISSN | 2372-1782 | ISBN | Medium | ||
| Area | Expedition | Conference | |||
| Notes | Approved | no | |||
| Call Number | Serial | 1219 | |||
| Permanent link to this record | |||||