Kumar, S., Wang I. Chan, C., Hu, Q., & Reno, J. L. (2011). A 1.8-THz quantum cascade laser operating significantly above the temperature of ω/kB. Nat. Phys., 7.
Abstract: Several competing technologies continue to advance the field of terahertz science; of particular importance has been the development of a terahertz semiconductor quantum cascade laser (QCL), which is arguably the only solid-state terahertz source with average optical power levels of much greater than a milliwatt. Terahertz QCLs are required to be cryogenically cooled and improvement of their temperature performance is the single most important research goal in the field. Thus far, their maximum operating temperature has been empirically limited to ~ω/kB, a largely inexplicable trend that has bred speculation that a room-temperature terahertz QCL may not be possible in materials used at present. Here, we argue that this behaviour is an indirect consequence of the resonant-tunnelling injection mechanism employed in all previously reported terahertz QCLs. We demonstrate a new scattering-assisted injection scheme to surpass this limit for a 1.8-THz QCL that operates up to ~1.9ω/kB (163 K). Peak optical power in excess of 2 mW was detected from the laser at 155 K. This development should make QCL technology attractive for applications below 2 THz, and initiate new design strategies for realizing a room-temperature terahertz semiconductor laser.
|
Lee, B. G., Assefa, S., Green, W. M. J., Min Yang, Schow, C. L., Jahnes, C. V., et al. (2011). Multichannel high-bandwidth coupling of ultradense silicon photonic waveguide array to standard-pitch fiber array. J. Lightwave Technol., 29(4), 475–482.
Abstract: A multichannel tapered coupler interfacing standard 250-μm-pitch low-numerical-aperture (NA) polarization-maintaining fiber arrays with ultradense 20- μm-pitch high-NA silicon waveguides is designed and fabricated. The coupler is based on an array of 12 dual-core glass waveguides on 250-μ m pitch that are tapered to a 20- μm pitch, simultaneously providing both pitch and spot-size conversion. At the wide end, the inner core matches the NA and mode profile of standard single-mode fiber. When drawn and tapered, the inner core “vanishes†and the outer core, surrounded by the clad, matches the NA and mode profile of the on-chip photonic waveguide. Ultradense high-efficiency coupling to an array of Si photonic waveguides is demonstrated using a 12-channel polarization-maintaining-fiber pigtailed tapered coupler. Coupling to Si waveguides is facilitated using SiON spot-size converters integrated into the Si photonic IC to provide 2-3-μm mode field diameters compatible with the tapered coupler. The tapered coupler achieves <; 1 dB coupling losses to photonic waveguides. Furthermore, eight-channel coupling is shown with less than -35 dB crosstalk between channels. Finally, a 640-Gb/s wavelength-division-multiplexing signal is coupled into four waveguides occupying 80 μm of chip edge, providing 160-Gb/s per-channel bandwidths.
|
Lobanov, Y., Tong, E., Blundell, R., Hedden, A., Voronov, B., & Gol'tsman, G. (2011). Large-signal frequency response of an HEB mixer: from 300 MHz to terahertz. IEEE Trans. Appl. Supercond., 21(3), 628–631.
Abstract: We present a study of the large signal frequency response of an HEB mixer over a wide frequency range. In our experiments, we have subjected the HEB mixer to incident electromagnetic radiation from 0.3 GHz to 1 THz. The mixer element is an NbN film deposited on crystalline quartz. The mixer chip is mounted in a waveguide cavity, coupled to free space with a diagonal horn. At microwave frequencies, electromagnetic radiation is applied through the coaxial bias port of the mixer block. At higher frequencies the input signal passes via the diagonal horn feed. At each frequency, the incident power is varied and a family of I-V curves is recorded. From the curves we identify 3 distinct regimes of operation of the mixer separated by the phonon relaxation frequency and the superconducting energy gap frequency observed at about 3 GHz and 660 GHz respectively. In this paper, we will present observed curves and discuss the results of our experiment.
|
Lobanov, Y. V., Tong, C. - Y. E., Hedden, A. S., Blundell, R., Voronov, B. M., & Gol'tsman, G. N. (2011). Direct measurement of the gain and noise bandwidths of HEB mixers. IEEE Trans. Appl. Supercond., 21(3), 645–648.
Abstract: The intermediate frequency (IF) bandwidth of a hot electron bolometer (HEB) mixer is an important parameter of the mixer, in that it helps to determine its suitability for a given application. With the availability of wideband low noise amplifiers, it is simple to measure the performance of an HEB mixer over a wide range of IF at a fixed LO frequency using the standard Y-factor method. This in-situ method allows us to measure both the gain and noise bandwidths simultaneously. We have also measured mixer output impedance with a vector network analyser. Intrinsic time constant has been extracted from the impedance data and compared to the mixer's bandwidths determined from receiver Y-factor measurement.
|
Lupascu, A. (2011). Nonlinear dynamics: Quantum pendula locked in. Nat. Phys., 7(2), 100–101.
Abstract: A study of the autoresonant behaviour of a superconducting pendulum reveals that quantum fluctuations determine only the initial oscillator motion and not its subsequent dynamics. This could be important in the development of more efficient methods for reading solid-state qubits.
|
